Zhejiang Aokai Electric Co., Ltd. is one of the leading manufacturers and suppliers of add200ij dc relay handling electric forklift contactor hydraulic dc oil pump motor start switch in China. If you're going to buy CE approved add200ij dc relay handling electric forklift contactor hydraulic dc oil pump motor start switch, welcome to get more information from our factory. Good service and quality products are available.
ADD250-I 24VDC SPST NO DC Relay For Lift Table Power Unit
Electric Forklift DC Motor Contactor 200Amps Aokai contactor
Contact Arrangement: 1NO
Working Duty: Intermittent 200A load
Insulation Resistance: 100MΩ(1000VDC)
IP protection level: IP67
Load Terminal: M8 External Thread
Vibration: 3.5G, 10-200Hz, 1/2 Sine Wave (Power On)
Shock: 20G (Power On)
Relative Humidity: 5%-95% RH
Dimension: 76.8*70.6*68.5mm
Electrical Life: 50,000 cycles (48V/200A)
Load Wiring Torque: 8 - 10N.m
Coil Wiring Torque: 2 - 3N.m
Features
◪ Intermittent 200A load.
◪ It has one set of normally open contacts.
◪ Coil power consumption ≤24W.
◪ The insulation resistance is up to 100MΩ (1,000VDC), the withstand voltage
between the contact and the coil is 2kV.
◪ IP protection level: IP67.
◪ Compliant with IEC 60664-1, GB/T14048.1 and GB/T14048.4 requirements.
◪ Compliant with RoHS (2015/863/EU), REACH (1907/2006/EC) requirements.
◪ Safety certificate: CE, RoHS
Specifications
|
Performance Parameters (at 23℃) |
||
|
Contact Arrangement |
1NO |
|
|
Contact Resistance |
≤5mΩ |
|
|
Contact Voltage Drop |
≤80mV (at 200A) |
|
|
Overload Current |
≤7le, ≯1s |
|
|
Temperature Range |
-40℃~55℃ |
|
|
Load Terminal |
M8 External Thread |
|
|
Humidity |
5%~95%RH |
|
|
External Dimension |
76.8mm*70.6mm*68.5mm |
|
|
Operating Duty |
Intermittent |
|
|
Electrical Durability with Load (Resistive) |
≥50,000 Times |
|
|
Load Wiring Torque |
8-10N.m |
|
|
Pull-In Voltage |
≤70% Us |
|
|
Drop-Out Voltage |
5%-40% Us |
|
|
Contact Bounce Period |
≤5ms |
|
|
Pull-In Time |
≤30ms |
|
|
Drop-Out Time |
≤30ms |
|
|
Dielectric Strength |
Between Main Contacts |
50Hz/60Hz 1,500VAC/1min |
|
Between Main Contacts and Coil |
50Hz/60Hz 1,500VAC/1min |
|
|
Insulation |
Initial State |
100MΩ 1min |
|
After Electrical Life |
50MΩ 1min |
|
|
Shock |
Stability |
20g (Power On) |
|
Strength |
50g |
|
|
Vibration |
3.5g, 10~200Hz, 1/2 Sine Wave (Power On) |
|
|
Mechanical Durability |
≥100,000 Times |
|
|
Coil Wiring Torque |
2 - 3 N.m | |
|
ADC300I Coil Parameters |
||||
|
Coil Voltage |
Pull-In Voltage |
Drop-Out Voltage |
Coil Resistance |
Coil Power Consumption |
|
12V |
≤70%Us |
5%-40%Us |
6Ω±10% |
24W±10% |
|
24V |
≤70%Us |
5%-40%Us |
24Ω±10% |
24W±10% |
|
36V |
≤70%Us |
5%-40%Us |
54Ω±10% |
24W±10% |
|
48V |
≤70%Us |
5%-40%Us |
96Ω±10% |
24W±10% |
|
60V |
≤70%Us |
5%-40%Us |
150Ω±10% |
24W±10% |
|
72V |
≤70%Us |
5%-40%Us |
216Ω±10% |
24W±10% |
Product Introduction
This series DC Contactor is widely used in electromobiles, electric forklifts, electric winches, engineering machinery, etc.
Model Coding
Wiring Diagram
Outline Installation Dimension Drawing
Note: These datas are only for customer selection reference, AOKAI has tried the best to ensure the accuracy of the information. Product
specifications and parameters may be changed due to product improvement etc., they may be inconsistent because of not updated in time.
For the specific parameters and performance of each product, please refer to the samples provided by AOKAI and the corresponding signed
and controlled specification.
Note: These datas are only for customer selection reference, AOKAI has tried the best to ensure the accuracy of the information.
Product specifications and parameters may be changed due to product improvement etc., they may be inconsistent because of
not updated in time. For the specific parameters and performance of each product, please refer to the samples provided by AOKAI
and the corresponding signed and controlled specification.
Hot Tags: add200ij dc relay handling electric forklift contactor hydraulic dc oil pump motor start switch, manufacturers China, suppliers, factory, CE
